Barrel Spares

2" cap fitted with a combined inlet & pressure release valve and fits the Weltonhurst 5 gallon Standard barrels.

It can be used with either a Hambleton Bard Super 20 or Super 30 cylinder (the valve on this cap CAN NOT be used with the 8grm CO2 bulbs)

This valve has a pin to perce the 8g C02 bubls and can be fitted to king keg barrels & also standard barrels + bulb holder, insert the C02 bulb screw on to the valve to inject the gas.

2" cap fitted with a combined inlet & pressure release valve and fits the Weltonhurst 5 gallon Standard barrels.

( The valve on this cap IS USED with the 8grm CO2 bulbs and is fitted with a pin to pierce the bulb.)

The centre of this cap is bored to accept a brass valve. It comes fitted with a seal. fits the weltonhurst 5 gallon Standard bottom tap barrels.

This cap has a moulded in pressure relief valve It comes fitted with a seal. fits the weltonhurst 5 gallon Standard bottom tap barrels.

This 4 inch cap will fit both the King Keg Bottom & Top Tap Barrels.

It comes with O Ring and inlet / pressure relief valve It can be used with either a Hambleton Bard S20 or S30 Gas cylinder

This 4 inch cap will fit both the King Keg Bottom and Top Tap and micro brewery Barrels.

It comes with O Ring and inlet / pressure relief valve (The valve on this cap IS USED with the 8grm CO2 bulbs and is fitted with a pin to pierce the bulb.

A replacement 4"cap bored To fit both the King Keg bottom and top tap and micro brewery barrels.

it comes with O Ring the centre of this cap is bored to accept a brass valve.

Suitable for King Keg and Brewmaster barrel caps, To aid the undoing or tightening of the barrel cap.

This pack is for People who have a standard 2 or 5 gallon barrel and need to inject CO2 into The barrel This cap has a combined inlet Pressure release valve fitted with a pin to pierce 8 gram CO2 bulbs and it comes complete with a red plastic CO2 bulb holder.

The pin makes this cap and valve unsuitable for use with any other form of gas injection cylinder. The seal between this cap and the barrel is made with a white flat-sectioned washer.

This adaptor enables the standard 8-gram CO2 bulbs to be used with threaded s20 / s30 barrel valves.

8grm CO2 Gas Bulb holder for the steel pin valve

This is the valve that is fitted to King Keg barrels And Also standard barrels

This is the valve that is fitted to King Keg barrels And Also standard barrels

Replacement Beer Float For The Top Tap King Keg

for either the top or bottom tap King Keg And Standard barrels.

Consisting of the cap clear ‘O’ ring, And White 'O' Ring black valve sealing washer, black gas inlet sealing sleeve, brown pressure release rubber and the black injection valve ‘O’ ring

Tap With washer and back nut fits barrels with 2" & 4" Diameter necks.

Also works under pressure, gives a smother flow on king kegs it is easer to open than the drum tap also a float can be attached in to the back of the tap.

Spare tap back nut and washer for the bottom and top tap king keg and most other beer barrels with a 4" neck.

Spare tap and washer to fit Bottom tap barrels with 2" Diameter necks.

This has a 3/4" BSP thread and it fits the Plastic Drum Tap fitted to King Keg barrels.

A replacement tap washer, made from a hard black rubber and normally fitted on the Drum Taps of 4" neck barrels and 2".

Replacement cap seal for the 2" barrel caps that are sealed with a flat white cap washer.

Replacement 4" "O" ring for the king keg top & bottom tap & Brewmaster barrels cap.

Brass valve inlet rubber black for the combined gas inlet and pressure relief valve.