Barrel Spares

2" cap fitted with a combined inlet & pressure release valve and
fits the Weltonhurst 5 gallon Standard barrels. It can be
used with either a Hambleton Bard Super 20 or Super 30 cylinder

(the valve on this cap CAN NOT be used with the 8grm CO2 bulbs)

CO2 Injector System & 2 Sparklets 8 grm bulbs

This pack is for People who have a standard 2 or 5 gallon
barrel with a 2" opening and need to inject CO2 into The barrel This cap has a combined inlet & pressure release valve fitted with a pin to pierce 8 gram CO2 bulbs and it comes complete with a red plastic CO2 bulb holder. The pin makes this cap and valve unsuitable for use with any other form of gas injection cylinder. The seal between this cap and the barrel is made with a white flat-sectioned washer.

2" cap fitted with a combined inlet & pressure release valve and
fits the Weltonhurst 5 gallon Standard barrels.

( The valve on this cap IS USED with the 8grm CO2 bulbs and is fitted with a pin to pierce the bulb.)

This 4 inch cap will fit both the King Keg Bottom and Top Tap
Barrels. it comes with O Ring and inlet / pressure relief valve It can be used with either a Hambleton Bard S20 or S30 Gas cylinder

This 4 inch cap will fit both the King Keg Bottom and Top Tap and micro brewery Barrels. it comes with O Ring and inlet / pressure relief valve (The valve on this cap IS USED with the 8grm CO2 bulbs and is fitted with a pin to pierce the bulb.

Barrel cap spanner for 4 inch caps

Suitable for King Keg and Brewmaster barrel caps, To aid the undoing or tightening of the barrel cap.

S20 / S30 BARREL VALVE (BRASS)

This is the valve that is fitted to King Keg barrels And Also standard barrels

PIN VALVE FOR 8g CO2 BULBS
with bulb holder

Replacement Pin Valve (BRASS) For 8gm Bulbs

8grm CO2 Gas Bulb holder for the steel pin valve

Latstock Beer Float

Replacement Beer Float For The Top Tap King Keg

Complete set of cap and valve seals

for either the top or bottom tap King Keg And Standard barrels, consisting of the cap clear ‘O’ ring, And White 'O' Ring black valve sealing washer, black gas inlet sealing sleeve, brown pressure release rubber and the black injection valve ‘O’ ring

Quick Serve Lever Tap

spare tap and washer to fit Bottom tap barrels with 2" Diameter necks.

Drum Tap

Spare tap back nut and washer for the Bottom and Top Tap King Keg and most other beer barrels with a 4" neck.

Tap Backnut

This has a 3/4" BSP thread and it fits the Plastic Drum Tap fitted to King Keg barrels

A replacement 2"cap bored

The centre of this cap is bored to accept a brass valve. It comes fitted with a seal. fits the weltonhurst 5 gallon Standard bottom tap barrels.

A replacement 4"cap bored
To fit both the King Keg Bottom and Top Tap and micro brewery Barrels. it comes with O Ring the centre of this cap is bored to accept a brass valve.

Replacement cap seal for the 2" barrel caps that are sealed with a flat white cap washer.

Replacement 4" "O" ring for the king keg top & bottom tap & Brewmaster barrels cap

This adaptor enables the standard 8-gram CO2 bulbs to be used with threaded s20 / s30 barrel valves.

Brass valve inlet rubber black for the combined gas inlet and pressure relief valve.

Tap Washer - Black

A replacement tap washer, made from a hard black rubber and normally fitted on the Drum Taps of 4" neck barrels and 2"

Brass valve pressure relief rubber brown for the combined gas inlet and pressure relief valve.

Brass valve black sealing washer fits between the brass valve and the barrel cap.

2'' vented cap

This cap has a moulded in pressure relief valve It comes fitted with a seal. fits the weltonhurst 5 gallon Standard bottom tap barrels.

Wine fermenter lever tap and back nut

Tap With washer and back nut fits barrels with 2" & 4" Diameter necks.
Also works under pressure, gives a smother flow on king kegs it is easer to open than the drum tap also a float can be attached in to the back of the tap.